Hi,
I see the locations popping up on GEOMAP, but not the (WAN) links as shown in some example screenshots.
Anyone have a clue why this could be?
Cheers Erik
On Fri, 25 Aug 2017 11:35:35 +0200 Erik kempere@quakerchem.com wrote:
I see the locations popping up on GEOMAP, but not the (WAN) links as shown in some example screenshots.
Anyone have a clue why this could be?
Has NAV discovered your topology at all? E.g. when viewing your link ports in ipdevinfo, does it have information about neighbors and VLANs?
On Wed, 30 Aug 2017 09:10:32 +0000 Andreas Dobloug andreas.dobloug@usit.uio.no wrote:
Has NAV discovered your topology at all? E.g. when viewing your link ports in ipdevinfo, does it have information about neighbors and VLANs?
Yes, but it isn't updating.
Aha, but I was addressing Erik here, and I don't think you answer for him ;-)
Hello Morten,
Yes, it's filling up nicely as far as I can tell.
But the two links THAT show up now, don't make sense (1000Mps link, no loads).
CDP and VLANS are showing.........
Cheers Erik
-----Original Message----- From: Morten Brekkevold [mailto:morten.brekkevold@uninett.no] Sent: 30 August 2017 08:48 To: Erik Kemper kempere@quakerchem.com Cc: nav-users@uninett.no Subject: Re: GEOMAP
On Fri, 25 Aug 2017 11:35:35 +0200 Erik kempere@quakerchem.com wrote:
I see the locations popping up on GEOMAP, but not the (WAN) links as shown in some example screenshots.
Anyone have a clue why this could be?
Has NAV discovered your topology at all? E.g. when viewing your link ports in ipdevinfo, does it have information about neighbors and VLANs?
-- Morten Brekkevold UNINETT
QUAKER CHEMICAL CORPORATION DISCLAIMER: This message is intended only for the use of the individual or entity to which it is directed and may contain information that is privileged, confidential and exempt from disclosure under applicable law. If the reader of this message is not the intended recipient, you are hereby notified that any dissemination, distribution or copying of this communication is strictly prohibited. If you have received this communication in error, please notify the sender immediately by reply e-mail and delete the message and any attachments.
On Thu, 31 Aug 2017 06:30:54 +0000 Erik Kemper kempere@quakerchem.com wrote:
Hello Morten,
Yes, it's filling up nicely as far as I can tell.
But the two links THAT show up now, don't make sense (1000Mps link, no loads).
What doesn't make sense? Is 1000Mbps wrong, or is it just that no loads are shown? If you look at the involved ports in ipdevinfo, does NAV have data in the traffic counter graphs?
Unfortunately, the Geomap is notorious for problems with displaying updated load data.
I think it partly comes down to the fact that it tries to get data for the last 10 minutes, but since counter values are only collected every 5 minutes, and there is no guarantee that the latest data slot has been filled yet, a query for 10 minutes might give a single counter value. You need at least two data points to calculate a differential. So it might be an idea to have the Geomap default to 15 minute intervals instead.
Do you get load data if you open the "map options" panel and play around with the data interval?
Hi,
If I play with the map options, lines and edges are showing green and some load, but the links are still showing 1000Mbps, when it should (I think :-) ) show the WAN capacity (2, 4 155 Mbps)?
Cheers Erik
-----Original Message----- From: Morten Brekkevold [mailto:morten.brekkevold@uninett.no] Sent: 31 August 2017 08:54 To: Erik Kemper kempere@quakerchem.com Cc: nav-users@uninett.no Subject: Re: GEOMAP
On Thu, 31 Aug 2017 06:30:54 +0000 Erik Kemper kempere@quakerchem.com wrote:
Hello Morten,
Yes, it's filling up nicely as far as I can tell.
But the two links THAT show up now, don't make sense (1000Mps link, no loads).
What doesn't make sense? Is 1000Mbps wrong, or is it just that no loads are shown? If you look at the involved ports in ipdevinfo, does NAV have data in the traffic counter graphs?
Unfortunately, the Geomap is notorious for problems with displaying updated load data.
I think it partly comes down to the fact that it tries to get data for the last 10 minutes, but since counter values are only collected every 5 minutes, and there is no guarantee that the latest data slot has been filled yet, a query for 10 minutes might give a single counter value. You need at least two data points to calculate a differential. So it might be an idea to have the Geomap default to 15 minute intervals instead.
Do you get load data if you open the "map options" panel and play around with the data interval?
-- Morten Brekkevold UNINETT
QUAKER CHEMICAL CORPORATION DISCLAIMER: This message is intended only for the use of the individual or entity to which it is directed and may contain information that is privileged, confidential and exempt from disclosure under applicable law. If the reader of this message is not the intended recipient, you are hereby notified that any dissemination, distribution or copying of this communication is strictly prohibited. If you have received this communication in error, please notify the sender immediately by reply e-mail and delete the message and any attachments.
-
Andreas Dobloug -
Erik -
Erik Kemper
-
Morten Brekkevold